WLM WIFI range extender setup with different brand WIFI router can be using login method and using WPS push button method if your WLM range extender support WPS feature. WLM N19 Wifi Extender device supports only 2.4Ghz 300Mbps single band. If you Have a dual band Range extender that supports 450Mbps or 1200Mbps WIFI speed with Dual band combined wireless speed in 5G and in 2.4Ghz then you can also follow this setup guide.
WLM signal booster device is compatible with almost all leading brand wifi routers and access points. WLM N19 Wifi repeater device supports 4 external antenna alone with 1 Ethernet Port for wired connection and a WPS button for Reset and Setup.
WLM Wireless Extender Ethernet port lets you connect your Non WIFI devices such as NVR/DVR/ PC without wifi and Network printer. WLM Repeater device works with most brands so if you can follow this WLM WIFI extender Setup manual to connect WLM extender with your internet wifi router and increase signal range in no coverage area.
WLM Fastest WIFI Extender Setup using WPS method
WLM signal booster device connects with any wifi router using the WPS method only works if your WLM extender model supports the WPS button as well as your host wifi router supports the WPS button and is enabled from the router WPS settings. Follow the steps to configure the WLM range extender using the WPS button.
- Unbox WLM WIFI signal booster /Range extender device if first time setup.
- Plug into the power Socket near your Host Internet WIFI router that you want to extend the wifi range.
- Go to the WiFi Router and locate a WPS button beside the Ethernet ports or power button.
- Press the WPS button for 2 seconds and release the button.
- Within 2 minutes go to the WLM Extender device press the WPS button (Big button below LED light) for 2 seconds and release
- Wait for 40-50 seconds until the WPS button configuration finish.
- Check WiFi in mobile/Laptop and scan for Extender wifi name (Exsitng_WIFI_EXT) connect and confirm the internet working with Extender SSID.
- Unplug the extender device and place it in the location facing a low signal-issue button to make a centralized placement from the host wifi router can at least get 50% signal strength.
IF your WLM does not support the WPS feature or your main internet router not working with WPS button then you can follow the next method to setup WLM extender using login methods from mobile/laptop or Desktop.
Setup WLM Signal Booster from Mobile / Laptop /Desktop
To configure the WLM repeater device from mobile or PC you need a connection using wifi or wired LAN cable from WLM Ethernet ports.
- Plugin WLM range extender to power socket and wait for 50-60 seconds until it boots up.
- Open mobile wifi and connect to SSID showing “WIFI-Extender” if using a WiFi connection.
- For Lan connection connect the Lan cable to the Extender Lan port to the PC/Laptop Lan port.
- Open the web browser and access “my-extender.com” or open the http://192.168.11.1 IP address to the URL bar.
- Choose WIFI Extender mode and press the next button.
- You will get Extender settings and scanning for the network. after a few seconds, you will get a list of all wifi names running near your extender device.
- Select your Existing wifi SSID name from the list provide a password and tap the finish button. Make sure you are providing the WIFI password correctly to avoid the wrong configuration or you may get no internet issue.
- Wait 40-50 seconds until the extender device reboots and keep the monitor LED light to confirm the connection with your existing wifi network.
- If the Middle LED light glows Solid green check the wifi name showing in your
- Unplug the Extender and install it in the location where you facing the signal issue.
The Best WiFi Range Extender Device to boost Signal
Troubleshooting Question & Answer for WLM WiFi range extender
If you facing any issues or want to get answers to common problem questions then read below FAQ part.
WLM N19 Range Extenders support 5G WIFI band.
No, It’s a single-band Extender so only supports 2.4Ghz wifi Band and works with 2.4Ghz wifi only.
WLM Extender Device IP address or Login URL not working.
Make sure you are connected to the WLM extender default SSID name “MY-Extender” It’s connected without the internet.
How to Factory Reset WLM WiFi Extender Device?
Power ON the extender device and wait 50 seconds to boot up. Press the WPS button for 10-15 seconds to factory reset the range extender device.
why WLM extender showing limited or no internet?
While connecting the WLM extender to your Host wifi network, ensure you have the correct password to connect with your existing wifi network.
Factory reset the extender device and setup again with the proper WIFI password. Press the Reset button (WPS button big one the front side) for 10 seconds to restore factory settings.
Related Post
- How to Configure WiFi Blast Range Extender
- QLOCOM WiFi Extender Booster Setup to Boost Range
- Ultralink Wifi Extender Setup To Boost Wifi Signal
- BrosTrend WiFi Extender Setup To Boost WiFI Range